VistaSoft Monitor
Manual
© 2022-2025 DÜRR DENTAL SE
2506V010
Important information
About this document
This manual applies to VistaSoft Monitor version 06/2025 or higher.
This manual forms part of the software. It corresponds to the version of the software and the technical standards valid at the time of installation.
In the event of non-compliance with the instructions and information contained in this manual, the manufacturer and the distributor will not offer any guarantee or accept any liability for the safe operation and the safe functioning of the unit and the software.
The German version of the instructions is the original manual. All other languages are translations of the original manual.
Warnings and symbols
Warnings
The warnings in this document are intended to draw your attention to possible injury to persons or damage to machinery.
The following warning symbols are used:
General warning symbol
The warnings are structured as follows:
NOTICE
Description of the type and source of danger
Here you will find the possible consequences of ignoring the warning
Follow these measures to avoid the danger.
DANGER
Immediate danger of severe injury or death
WARNING
Possible danger of severe injury or death
CAUTION
Risk of minor injuries
NOTICE
Risk of extensive material/property damage
Other symbols
These symbols are used within this document and in the software:
Note, e.g. specific instructions regarding efficient and cost-effective use of the unit.
Refer to the accompanying electronic documents.
Manufacturer
Copyright information
All circuits, processes, names, software programs and units mentioned in this document are protected by copyright.
The Installation and Operating Instructions must not be copied or reprinted, neither in full nor in part, without written authorisation from the copyright owner.
Safety
Intended purpose
The software is used to display, configure and analyse device information from the manufacturer-owned devices, as well as to manage their maintenance and servicing.
Intended use
This software is used for monitoring the manufacturer's own devices on the computer.
The software provides the following functionality:Collecting, analyzing, signaling and documenting messages and error situations in real-time
Displaying technical data and physical information
Supporting maintenance
Documenting operation
Adjustment of device settings
Saving of data in cloud
The data can also be made accessible to third parties (retailers or service partner) by the dentist with the explicit consent via interface.
Improper use
The software supplements the function of the display panel for amalgam separator monitoring. However, it does not replace the display panel.
Any other usage or usage beyond this scope is deemed to be improper. The manufacturer accepts no liability for damages resulting from this. In these cases the user/operator will bear the sole risk.
General safety information
When using the software, always comply with all guidelines, laws and other rules and regulations that are applicable at the site of operation.
Do not modify the software.
Comply with the installation instructions and software manual.
Specialist personnel
Operation
Persons using the software must be able to guarantee safe and correct operation based on their training and experience.
Make sure every operator is trained in the use of the software.
Cybersecurity measures (security context)
The software is installed on a computer in the local IT network and is then connected to a cloud application.
Therefore, the security context, which is a shared responsibility between the manufacturer and operator in terms of cybersecurity, must be taken into account.
The following administrative measures are required:
Train employees in security and data protection.
Appoint a data protection officer.
Appoint a medical IT risk manager.
Use of the IEC 80001-1 standard is recommended to manage security risks for medical IT networks.
The configuration of a medical IT network requires the expertise of a network administrator.
The following changes to a medical IT network can create new security risks that require a reassessment of the risk analysis:Changes to the IT network configuration
Adding components (hardware or software) to the medical IT network
Removing components from the medical IT network
Updating or modernizing components in the medical IT network
Report cybersecurity incidents to the manufacturer at
incidents@duerrdental.com.The following technical measures must be taken by the operator in order to use the software safely:
Protect the medical IT network with a firewall and antivirus software.
Disable all services, applications and network protocols that are unnecessary or unsafe.
If possible, use a network connected by cables.
Look for evidence of possible virus infection and, if applicable, check with the antivirus software and remove the virus.
Always keep the software used up to date and make sure you are working with the latest version, particularly with regard to the operating system, firewall and antivirus software.
Make sure that only trustworthy content is downloaded. Only install software and firmware updates that have been authenticated by the manufacturer.
Regularly check the integrity of the software or firmware.
Check the system requirements prior to every installation.
Segment the medical IT network to an extent that makes sense.
Use suitable user authentication and user authorisation within the operating system. Only assign the necessary rights to the user accounts.
Restrict administrative roles to a very limited number of accounts.
Use the user administration system offered by the software or medical devices.
Apply the generally accepted standards and requirements for the assignment of passwords.
Encrypt all data containing personal information.
Perform regular data backups.
Check external storage media (e.g. USB sticks, memory cards) before they are connected to the medical IT network.
Restrict Internet access to a minimum.
Check e-mails and attachments for potentially malicious content.
Secure hardware against unauthorized access (IT network, server and connected devices).
 | For more information, see “Cybersecurity White Paper”. |
Product description
Function
The software is installed on a computer in the local practice network and is connected to the devices of Dürr Dental in the practice.
If there is a message for a device in the practice, the software transfers the message to the cloud (vistasoftmonitor.com). In addition, a message of the VS Monitor Notifier is shown in the task bar.
The current status of the devices as well as any pending maintenance can be viewed using a browser.
The devices can optionally be assigned to a participating service partner. The service partner automatically receives the devices and practices assigned to them in their view.
- 1Local practice network
- 2Computer in the local network with server installation
All compatible, manufacturer-owned devices that are network-compatible can be connected to the software.
For the current overview of supported devices, see www.duerrdental.com/en/vistasoftmonitor/.
Devices lacking a network connection can be connected to the software using the Connect Box.
System requirements
Requirements for server installation of the VistaSoft Monitor software on a server or computer in the practice network:
Operating system: | Microsoft Windows 10 (version 1809 or higher) Microsoft Windows 11 Microsoft Windows Server 2019 Microsoft Windows Server 2022 Microsoft Windows Server 2025 |
Graphics card: | Resolution ³ 1280 x 1024 (recommended) |
Interface: | Ethernet, DHCP/dynamic allocation of IP addresses Internet |
Ports required: | TCP: 502, 512, 514, 50123, 25565 UDP: 1900, 45123, 45124, 45125 |
Additionally required software: | Browser (Mozilla Firefox, Google Chrome or Microsoft Edge, current version in each case) For connecting image plate scanner: VistaSoft server or single-user installation (from version 3.0.20) on the same computer |
Peripheral equipment required: | Audio reproduction (sound card, loudspeaker) recommended |
Just a browser is needed for the user interface of the cloud.
The network connection of the devices needs to be stable, e.g. via LAN or via a stable WLAN.
Installation
The server software is being installed on a computer in the local network. This computer serves as the interface to the cloud and needs to have Internet access.
Note for the server software:Install the server software on a computer that is always running.
Recommended: The server of the practice network. If not possible: Any computer, e.g. reception PC
Run the server software on only one computer in the network
VistaSoft Monitor is not compatible with Tyscor Pulse. Deinstall Tyscor Pulse.
Imaging software VistaSoft (from version 3.0.20) installed on the same computer as the server.
The first time VistaSoft is started, VistaSoft Monitor is automatically downloaded and installed. If no Internet connection is available then the software can also be downloaded and installed later on.
If VistaSoft (from version 3.0.20) and VistaSoft Monitor were installed together, no additional installation of VistaSoft Monitor in the practice network is necessary.
Server installation
Requirements:
✓Computer complies with the system requirements (see System requirements).
✓Computer and devices are connected to the local network and the Internet.
Only trained experts are permitted to install and commission the software.
1.Downloading software from the download area at www.duerrdental.com (http://qr.duerrdental.com/Software_VSMonitor).
2.Double-click VSMonitor-...exe.
3.Follow the instructions given by the installation wizard.
4.Click Install to complete the installation.Once the computer is connected to the Internet, it will automatically check for updates immediately after installation. If new updates are available, they are automatically downloaded and installed.
Following the installation, the Notifier is visible in the task bar as an icon.
Then VistaSoft Monitor needs to be configured on the computer with the server installation Registering the practice account.
Proxy settings
Some practices use a proxy to control access to the Internet.
In this case the proxy settings will need to be configured so that the VS Monitor Legacy Connector (LC) can connect to the cloud.
1.Open the installation directory of VS Monitor. Default path: C:\Program Files\Duerr\VS Monitor
2.Right-click the file proxy-config.ini and open it with Notepad.Here, select Run as administrator.
3.Fill in the following entries for the proxy used (example values in italics): [Proxy]host=proxy.example.comport=1080user=username*pass=password** Optional. Leave this empty if the proxy does not require any authentication.
4.Save and close the file.
5.Open Task Manager and switch to the Services tab.
6.Restart Legacy Connector Service under Win Services.
7.Double-click the icon on the desktop to restart VS Monitor Notifier.
on the desktop to restart VS Monitor Notifier.Registering the practice account
The first time a user logs in on the computer with the server installation of VistaSoft Monitor all devices that are on the network are automatically assigned to this user.
The user can then log in from any end device via the user interface to monitor their devices.
1.In the task bar, click Notifier.orClick on Start > Dürr Dental VS Monitor > VS Monitor Notifier.
Notifier.orClick on Start > Dürr Dental VS Monitor > VS Monitor Notifier.2.Click SIGN-Up to create a new user account.
An activation link for confirmation of the user account will be sent by email.
When licensing VistaSoft, a user account is automatically created and the email with activation link is sent.
3.If a user account at duerrdental.net exists already, click LOGIN to log-in the user.
The cloud user interface is opened in the browser.
Configuration
VS Monitor distinguishes between two user groups:
Practice:
Access to devices inside the practice, necessary for the use of VS Monitor
Service partners:
Optional access by registered service partners on the practice
The configuration process in the practice is described below.
For service partner information, see VistaSoft Monitor for service partners
The following are required for the configuration of VistaSoft Monitor:
Computer in the local network with server installation of VistaSoft Monitor
User account (practice account) at vistasoftmonitor.com (see also Registering the practice account).
1.In the task bar, click on the Notifier .orClick on Start > Dürr Dental VS Monitor > VS Monitor Notifier.
.orClick on Start > Dürr Dental VS Monitor > VS Monitor Notifier.The user interface of VistaSoft Monitor opens in the browser.
The set-up of VistaSoft Monitor requires the following steps:
Managing the location
During installation, the 
main location is created automatically.
We recommend using an appropriate and meaningful name for the main location, e.g. "Dental practice Dr. Maier".
The main location can also be subdivided into additional locations, see Managing locations. This provides large organisations with a clear overview of the devices at the various locations.
Requirements:
✓Logged in as administrator of the organisation
1.In the navigation bar, click on 
Settings.
Settings.2.Click the location.
The dialog window opens.
3.Update the name and address of the organisation.
4.Click Save to confirm changes.
Managing members
Members are users who have access to the organisation in VS Monitor. They can only be added to the main location.
There are different roles with different access rights:
Role | Access rights |
|---|---|
Member | Querying device information |
Administrator | Managing locations Managing members Managing devices Setting device parameters |
Requirements:
✓Logged in as administrator of the organisation
1.In the navigation bar, click on Settings.
Settings.The available locations are displayed.
2.Select the main location.
3.Switch to the Members tab.
Add member
1.Click Add new member.
2.In the dialogue window, enter the e-mail address and select the role of the new member.
3.Click Save to confirm.
The new member receives an invitation via e-mail with access to the user interface.
Change role
1.In the list of members, click on 
next to the member.
next to the member.2.In the context menu, click on 
Change role.
Change role.3.In the selection list, select the desired role.
Delete member
1.In the list of members, click next to the member.
next to the member.2.In the context menu, click on 
Delete.
Delete.Enter contacts for notifications
If an important message (malfunction) occurs or maintenance work is due on a device, the software automatically messages the contacts that are registered in Messages.
Messages can be registered at all levels of the organization. If a message contact is presented greyed-out, the message contact is registered at a higher-level location.
Requirements:
✓Logged in as administrator of the organisation
1.In the navigation bar, click on Settings.
Settings.The available locations are displayed.
2.Select the location.
3.Switch to the Notifications tab.
4.Add an email address with Add new entry.
An initial email is sent. Confirm the VS Monitor-messages through the link in the email.
Delete an entry in Notifications
1.In the list, click next to the entry.
next to the entry.2.In the context menu, click on Delete.
Delete.Assigning a device to a location
Every device is automatically added to the device list and is initially assigned to the main location. If additional locations have been created, the device can be assigned to a different location.
Requirements:
✓Logged in as administrator of the organisation
1.Click on My Devices in the side bar.
The device list opens. New devices are assigned to the main location.
2.Click on the device you wish to assign to a different location.
3.Click on Settings via the More button.Select the location to which the device is to be assigned.
4.Click Save.
Configuring a service partner
Assigning the monitoring partner
A monitoring partner can be assigned to each device. The monitoring partner can view device information and adjust settings.
Devices that are monitored by a service partner are labelled with 
in the device list on the dashboard.
Contact the monitoring partner before the device is assigned to the monitoring partner. The monitoring partner may charge a fee.
Only monitoring partners registered with VS Monitor can be selected.
Requirements:
✓Logged in as administrator
1.Click on the device in the device list.
The device details are displayed.
2.Switch to the Service Partner tab.
3.Enter the monitoring partner and select from the selection list. Only those monitoring partners who are registered with VS Monitor are shown.
4.Agree with the Data privacy statement and mark the check box.
5.Click on Send.
The device is entered in the service partner's account together with the practice.
The service partner receives a notification about the new device in their 
inbox.
Registering the WasteWatch disposal partner for the amalgam collecting vessel
For amalgam separators, the WasteWatch function can be used to automatically assign companies to dispose of and deliver the amalgam collecting vessel.
When the amalgam collecting vessel is 95% full and needs to be replaced, a notification is sent to the registered companies. The notification contains the contact details and basic device information.
Requirements:
✓Logged in as administrator
1.Click on the device in the device list.
The device details are displayed.
2.Switch to the Service Partner tab.
3.Enter the name and e-mail address of the waste management company.
4.Enter the name and e-mail address of the supplier company.
5.Activate the WasteWatch function.
6.Click on Send.
An e-mail with an activation link will be sent to the company. The company has 30 days to confirm the request by clicking on the activation link.
The status displayed depends on the company's response:Pending: The request is not yet confirmed.
Logged in: The company has confirmed the request. The notification function is active.
Logged out: The company has rejected the request.
Expired: The company did not respond within 30 days.
A new request can be sent.
WasteWatch is displayed as inactive until both companies (waste management and supplier) have the status Logged in.
Once both companies have the status Logged in, the WasteWatch function is active and the notifications are sent.
Usage
First steps
The views and rights vary depending on the role (administrator or member) and type of user (practice or service partner).
See also VistaSoft Monitor for service partners.
First steps of the process
Notifier
VS Monitor Notifier runs in the background on the computer in the local network on which the software is installed.
The Notifier has two functions:Display desktop messages on the computer.
Create connection between the devices and the cloud
Closing the user interface in the browser does not close the software on the computer. The software remains active, the Notifier continues to display the status in the task bar.
To re-open the user interface, click on the icon in the task bar.
The Notifier is visible in the task bar as an icon.
Once there is a new message for a device, VistaSoft Monitor sends the information to the cloud. The Notifier signals a new message in the task bar and as a Windows notification.
The display duration of the messages can be extended to up to 5 min. through the Windows settings.
The program icon of the Notifier in the task bar shows the highest current message level of the devices.
 | Trouble-free operation (no messages) |
 | Fault |
 | Warning |
 | Note |
 | Interrupted connection to the devices |
The Notifier can be ended or the connection to the cloud disconnected through the context menu in the task bar (right mouse button on program symbol):
Deactivate desktop messages | The messages on the desktop are deactivated. The connection between the devices and the cloud remains. See also Notifier messages |
Disconnect cloud connection | The connection to the cloud is disconnected. No device information and messages will be transferred to the cloud any longer. |
Open VS Monitor | The cloud user interface is opened in the browser. |
Licences | The additional licence terms are displayed. |
Notifier messages
Deactivate desktop messages
1.Use the right mouse button to click on the symbol in the task bar and click on Deactivate desktop messages in the context menu.
in the task bar and click on Deactivate desktop messages in the context menu.Activate desktop messages again
1.Start VS Monitor Notifier (through the desktop link or start).
The cloud user interface opens.
2.Log in to the cloud.
Cloud connection
If the connection from the Notifier to the cloud is disconnected, no more device information or messages are transferred to the cloud.
Disconnect connection to the cloud
1.With the right mouse button, click on the symbol in the task bar and click on Disconnect cloud connection in the context menu.
in the task bar and click on Disconnect cloud connection in the context menu.Restore connection to the cloud
1.Start VS Monitor Notifier (through the desktop link or start).
The cloud user interface opens.
2.Log in to the cloud.
Cloud-based user interface
There are two ways to open the user interface:
1.Open https://vistasoftmonitor.com in the browser.orOn computers with server installation: Click Notifier .
.
- 1Navigation bar
- 2Content area
The cloud user interface consists of the navigation bar and the content area.
The content area varies depending on the view chosen in the navigation bar.
Different views can be selected in the navigation bar depending on the role of the logged-in user:
 | Dashboard | Start page, overview of device status and locations The Maintenance area is only displayed when maintenance is due. |
| Inbox | Information for the practice:
|
 | My devices | Information about all devices present in the local network If devices are in the status malfunction, warning or note, the number of these devices is specified in the navigation bar. The background colour shows the highest message level that has occurred. see also My devices |
 | Product search | Search for information on products from Dürr Dental by serial number, order number or product name. The type plate can also be scanned easily in the search using the app. |
 | Saved documents | Documents marked as favourites |
 | Product registration 2+1 | Register a new device with Dürr Dental in order to request an extension of warranty coverage. |
| Settings | Create and edit locations, users and notifications |
Activating desktop messages in the browser
The browser offers to accept notifications from this website when logging into the cloud for the first time. This means that in future desktop messages from VS Monitor will be displayed when the browser is open on this computer. The VS Monitor website does not need to be open for this.
The messages can be activated/deactivated at any time via the browser settings.
My devices
All devices that are connected to the software are displayed in the My Devices view.
The status of the device is indicated by the icon in the device list:
 | Normal operation |
 | Error Operation of the device interrupted |
 | Warning Operation of the device restricted |
 | Device offline Connection to device is interrupted, no current information about the device status, e.g. device switched off or not connected to the network |
Further information in the device list:
| Monitoring of the device by service partner active |
 | Maintenance work due, see Maintenance |
1.In the navigation bar, click My Devices.
My Devices.2.To search for devices, go to the Search field and enter a product name, serial number (SN), order number (REF) or category.
Search field and enter a product name, serial number (SN), order number (REF) or category. 3.To filter the device list, select the organisation, category or status.
4.Click a device to have its details displayed.
- 1Basic information
- 2Tabs of the device details
The device status, the product designation, the order number and the serial number are displayed in the Basic Information for the device, as well as the information when it was last online.
The following information can be queried using the Tabs:
Dashboard | Overview of the current status of the device and display of basic information |
Messages | All messages of the device can be queried. The messages are sorted in order of time. You can search the list by code or message. |
Documents | Available instructions and additional information from the download centre at duerrdental.com (for service partners, also duerrdental.net) |
Service partner | The service partner of the device can be stored. |
Parameters | Parameters of the device that can be queried or adjusted (depending on the role of the user, e.g. Admin) |
Maintenance | List of maintenance work with specification of when due and the required replacement parts |
Further settings for the device can be accessed via the More button:
Product registration 2+1 | Register this device with Dürr Dental to request an extension of the guarantee |
Settings | Set the device location |
Remove device The device is automatically added to the device list again when it is reconnected to the network. |
Image plate scanners transmit only the basic device data (e.g. messages, maintenance information) to VS Monitor. No image or patient data is transmitted.
The imaging software is required to use the image plate scanner or to set imaging parameters.
Dashboard
The Dashboard tab gives an overview of the device’s current status
In addition, basic information is displayed here, such as order number, serial number, firmware version, guarantee.
The current device parameters and the time to the next maintenance are specified, depending on the device.
Querying current messages
The detailed view Messages shows messages that have occurred for the device. Here, the messages are divided into the following categories:
| Fault e.g. a compressor unit has failed |
| Notice e.g. amalgam collecting container 95% full |
 | Note e.g. filter change required |
 | Information e.g. next service due in 30 days |
If a message in the malfunction or warning category appears for a device, the message appears under My devices in the cloud-based user interface. The icon in the device list changes.
The Notifier becomes active in the form of a balloon tip and the colour of the message level (e.g. ) is shown along with the icon in the task bar. If several messages occur, the colour of the highest message level is displayed.
1.To query details of the message, switch to the detail view of the device.
Viewing documents for the device
Further information available for a device (e.g. manuals or instructions as PDF documents or videos) is listed in the detailed view under Documents.
For service partners, all documents are displayed that are also available for this device in the duerrdental.net portal.
If documents are required more often, they can be added to the saved documents in the navigation bar.
1.In the detailed view of My Devices switch to the Documents tab.
2.To open a document, click 
.
.3.To view a video, click 
.
.Adjusting device parameters
You can query the set parameters for the device on the Parameters tab. Provided the user has the necessary rights, he/she can also make changes to the parameters for the device.
For diagnostic devices, parameters can only be changed on the device itself or via the imaging software.
1.In the detailed view of My Devices switch to the Parameters tab.
2.If required, make the necessary changes to a parameter and click Save to confirm.
Result:
The change is sent to the device. Once the parameter has been changed on the device, a message appears in the software.
No further changes can be made in the software until the change has been completed on the device.
Maintenance
The regular maintenance work is displayed on the Maintenance tab.
When maintenance is due, the Maintenance tab is highlighted with . In addition, an email is sent (see also Enter contacts for notifications).
The maintenance work is grouped by due date and can be expanded and collapsed.
With a click on Display replacement parts, the list of replacement parts needed for the maintenance work is displayed.
Confirm maintenance
Once a maintenance task has been performed, it can be confirmed by the administrator or technician.
1.Under My Devices select the device and switch to the Maintenance tab.
My Devices select the device and switch to the Maintenance tab.2.Select the maintenance task.
3.Click on Confirm.
4.Set the date in the dialog window, if necessary.
5.As administrator: Enter the name and email address of the service partner.
6.Click 
.
. The dialog window is closed. The maintenance interval is reset.
Open history
The maintenance task performed is displayed in the device history.
1.Under My Devices select the device and switch to the Maintenance tab.
My Devices select the device and switch to the Maintenance tab.2.Click on History.
The device history opens.
Device-specific information
Hygoclave 50
For legal reasons, the parameters for the sterilisation can only be set on the device itself and not via VS Monitor.
For connected Hygoclave 50, all new and existing sterilisation logs on the device are automatically stored locally on the computer on which the server installation is available in the local network.
The sterilisation logs are saved for each device (serial number) in the following directory:
C:\Documents\Dürr Dental\[Serial number]\[Year]\[Month]
My user account
The information and settings for the logged-in user are located at the bottom edge of the navigation bar.
Clicking the logged-in user takes you to a context menu with various functions:
 | My user account:
|
 | Change language |
 | Open help |
 | Open legal information / general terms of business |
 | Open privacy statement |
 | Log out user |
VistaSoft Monitor for service partners
VS Monitor provides service partners with an overview of the status of the devices assigned to them by different practices.
Due and pending maintenance work can also be retrieved via the cloud-based user interface.
Registering a service partner account
The service partner must be registered with Dürr Dental.
1.Register at https://www.duerrdental.com/register-vsm.
First steps
1.Open https://vistasoftmonitor.com in the browser.
- 1Navigation bar
- 2Content area
The cloud user interface consists of the navigation bar and the content area.
The content area varies depending on the view chosen in the navigation bar.
Different views can be selected in the navigation bar depending on the role of the logged-in user:
| Dashboard | Start page, overview of device status and locations The Maintenance area is only displayed when maintenance is due. |
| Inbox | Information for the service partner:
|
 | TechNews | Current information from Dürr Dental |
| My devices | Information about all devices present in the local network If devices are in the status malfunction, warning or note, the number of these devices is specified in the navigation bar. The background colour shows the highest message level that has occurred. see also My devices |
| Product search | Search for information on products from Dürr Dental by serial number, order number or product name. The type plate can also be scanned easily in the search using the app. |
| Saved documents | Documents marked as favourites |
| Product registration 2+1 | Register a new device with Dürr Dental in order to request an extension of warranty coverage. |
 | Spare parts catalogue | Link to the Dürr Dental spare parts catalogue – this opens a new browser window |
| Settings | Create and edit locations, users and notifications |
Activating desktop messages in the browser
The browser offers to accept notifications from this website when logging into the cloud for the first time. This means that in future desktop messages from VS Monitor will be displayed when the browser is open on this computer. The VS Monitor website does not need to be open for this.
The messages can be activated/deactivated at any time via the browser settings.
Managing locations
There are different types of locations for the organisational structure:
| Main location Location created automatically. It can be edited and renamed, but not deleted. Members (users) are managed here, see also Managing members. |
 | Region Location without address for grouping locations |
 | Location with address If the address of at least one location is registered, the locations are shown on the map in the |
The service partner automatically has a main location.
If a practice has assigned devices to the service partner and these have been confirmed by the service partner, the practice appears in the service partner's organisation as location.
For an improved overview, the locations can be combined into regions and locations. Individual notifications can be created for each location (see also Enter contacts for notifications).
Example of an organisational structure:
| ||
| ||
| ||
| ||
| ||
| ||
| ||
| ||
Requirements:
✓Logged in as administrator of the organisation
1.In the navigation bar, click on Settings.
Settings.The available locations are displayed.
Add location
1.Click Add location.
2.Select the higher-level location.
The dialog window opens.
3.Enter the name and, if applicable, address.All fields marked * must be completed.
If only a name is entered, a region is created.
With an address, a location is created.
4.Click Save.
Edit location
1.Click the location.
The dialog window opens.
2.Make changes as required and click Save to confirm.
Delete location
A location can only be deleted if no devices are assigned to it and if it has no dependent locations. All assigned devices and locations must be removed before deleting.
The higher-level main location cannot be deleted.
The dialog window opens.
2.Click .
.3.Confirm the deletion.
Managing members
Members are users who have access to the organisation in VS Monitor. They can only be added to the main location.
There are different roles with different access rights:
Role | Access rights |
|---|---|
Member | Querying device information |
Administrator | Managing locations Managing members Managing devices Setting device parameters |
Service Technician | Setting device parameters (Advanced) |
Requirements:
✓Logged in as administrator of the organisation
1.In the navigation bar, click on Settings.
Settings.The available locations are displayed.
2.Select the main location.
3.Switch to the Members tab.
Add member
1.Click Add new member.
2.In the dialogue window, enter the e-mail address and select the role of the new member.
3.Click Save to confirm.
The new member receives an invitation by e-mail with access to the user interface.
Change role
1.In the list of members, click on next to the member.
next to the member.2.In the context menu, click on Change role.
Change role.3.In the selection list, select the desired role.
Delete member
1.In the list of members, click on next to the member.
next to the member.2.In the context menu, click on Delete.
Delete.Enter contacts for notifications
If an important message (malfunction) occurs or maintenance work is due on a device, the software automatically messages the contacts that are registered in Messages.
Messages can be registered at all levels of the organization. If a message contact is presented greyed-out, the message contact is registered at a higher-level location.
Requirements:
✓Logged in as administrator of the organisation
1.In the navigation bar, click on Settings.
Settings.The available locations are displayed.
2.Select the location.
3.Switch to the Notifications tab.
4.Add an email address with Add new entry.
An initial email is sent. Confirm the VS Monitor-messages through the link in the email.
Delete an entry in Notifications
1.In the list, click next to the entry.
next to the entry.2.In the context menu, click on Delete.
Delete.My devices
- 1Basic information
- 2Tabs of the device details
The device status, the product designation, the order number and the serial number are displayed in the Basic Information for the device, as well as the information when it was last online.
The following information can be queried using the Tabs:
Dashboard | Overview of the current status of the device and display of basic information, see Dashboard |
Messages | All messages of the device can be queried, see Querying current messages. The messages are sorted in order of time. You can search the list by code or message. |
Documents | Available instructions and additional information from the download centre at duerrdental.com and duerrdental.net, see Viewing documents for the device |
Parameters | Parameters of the device that can be queried or adjusted (depending on the role of the user, e.g. Admin), see Adjusting device parameters |
Maintenance | List of maintenance work with specification of when due and the required replacement parts, see Maintenance |
Further settings for the device can be accessed via the More button:
Product registration 2+1 | Register this device with Dürr Dental to request an extension of the guarantee |
Spare parts catalogue | Link to spare parts for the device in the spare parts catalogue |
Settings | Remove device The device is automatically added to the device list again when it is reconnected to the network. |
Troubleshooting
Tips for operators and service technicians
Any repairs exceeding routine maintenance may only be carried out by qualified personnel or our service.
Error | Possible cause | Remedy |
|---|---|---|
The device is not displayed in the list of devices | The device is not connected to the network |
|
Incorrect firewall settings |
| |
Incorrect network settings in the Control Panel |
| |
Obsolete device firmware or device is not supported | If device is supported:
| |
User is not logged into VS Monitor through the Notifier. |
| |
Incorrect network configuration |
| |
Device status is not being refreshed, messages are not displayed | Connection to the device interrupted |
|
Service VistaSoft Monitor on computer (server installation) stopped |
| |
Internet connection is interrupted |
| |
User is not logged into VistaSoft Monitor through the Notifier. |
| |
Information on the dashboard of the device restricted | Firmware version on device outdated |
|
No status for image plate scanners in VS Monitor | Installation of VS Monitor and VistaSoft not on the same computer or wrong version |
|
Appendix
Additional licensing terms
Parts of the product are based on third-party image libraries with a large number of available licences that are not covered by the EULA.
Qt framework (LGPL-3)
jwcrypto (LGPL-3)
pycountry (LGPL-2)
Apache License 2.0
Apache License
Version 2.0, January 2004
http://www.apache.org/licenses/
TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION
1. Definitions.
"License" shall mean the terms and conditions for use, reproduction, and distribution as defined by Sections 1 through 9 of this document.
"Licensor" shall mean the copyright owner or entity authorized by the copyright owner that is granting the License.
"Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common control with that entity. For the purposes of this definition, "control" means (i) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficial ownership of such entity.
"You" (or "Your") shall mean an individual or Legal Entity exercising permissions granted by this License.
"Source" form shall mean the preferred form for making modifications, including but not limited to software source code, documentation source, and configuration files.
"Object" form shall mean any form resulting from mechanical transformation or translation of a Source form, including but not limited to compiled object code, generated documentation, and conversions to other media types.
"Work" shall mean the work of authorship, whether in Source or Object form, made available under the License, as indicated by a copyright notice that is included in or attached to the work (an example is provided in the Appendix below).
"Derivative Works" shall mean any work, whether in Source or Object form, that is based on (or derived from) the Work and for which the editorial revisions, annotations, elaborations, or other modifications represent, as a whole, an original work of authorship. For the purposes of this License, Derivative Works shall not include works that remain separable from, or merely link (or bind by name) to the interfaces of, the Work and Derivative Works thereof.
"Contribution" shall mean any work of authorship, including the original version of the Work and any modifications or additions to that Work or Derivative Works thereof, that is intentionally submitted to Licensor for inclusion in the Work by the copyright owner or by an individual or Legal Entity authorized to submit on behalf of the copyright owner. For the purposes of this definition, "submitted" means any form of electronic, verbal, or written communication sent to the Licensor or its representatives, including but not limited to communication on electronic mailing lists, source code control systems, and issue tracking systems that are managed by, or on behalf of, the Licensor for the purpose of discussing and improving the Work, but excluding communication that is conspicuously marked or otherwise designated in writing by the copyright owner as "Not a Contribution."
"Contributor" shall mean Licensor and any individual or Legal Entity on behalf of whom a Contribution has been received by Licensor and subsequently incorporated within the Work.
2. Grant of Copyright License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable copyright license to reproduce, prepare Derivative Works of, publicly display, publicly perform, sublicense, and distribute the Work and such Derivative Works in Source or Object form.
3. Grant of Patent License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable (except as stated in this section) patent license to make, have made, use, offer to sell, sell, import, and otherwise transfer the Work, where such license applies only to those patent claims licensable by such Contributor that are necessarily infringed by their Contribution(s) alone or by combination of their Contribution(s) with the Work to which such Contribution(s) was submitted. If You institute patent litigation against any entity (including a cross-claim or counterclaim in a lawsuit) alleging that the Work or a Contribution incorporated within the Work constitutes direct or contributory patent infringement, then any patent licenses granted to You under this License for that Work shall terminate as of the date such litigation is filed.
4. Redistribution. You may reproduce and distribute copies of the Work or Derivative Works thereof in any medium, with or without modifications, and in Source or Object form, provided that You meet the following conditions:
(a) You must give any other recipients of the Work or Derivative Works a copy of this License; and
(b) You must cause any modified files to carry prominent notices stating that You changed the files; and
(c) You must retain, in the Source form of any Derivative Works that You distribute, all copyright, patent, trademark, and attribution notices from the Source form of the Work, excluding those notices that do not pertain to any part of the Derivative Works; and
(d) If the Work includes a "NOTICE" text file as part of its distribution, then any Derivative Works that You distribute must include a readable copy of the attribution notices contained within such NOTICE file, excluding those notices that do not pertain to any part of the Derivative Works, in at least one of the following places: within a NOTICE text file distributed as part of the Derivative Works; within the Source form or documentation, if provided along with the Derivative Works; or, within a display generated by the Derivative Works, if and wherever such third-party notices normally appear. The contents of the NOTICE file are for informational purposes only and do not modify the License. You may add Your own attribution notices within Derivative Works that You distribute, alongside or as an addendum to the NOTICE text from the Work, provided that such additional attribution notices cannot be construed as modifying the License.
You may add Your own copyright statement to Your modifications and may provide additional or different license terms and conditions for use, reproduction, or distribution of Your modifications, or for any such Derivative Works as a whole, provided Your use, reproduction, and distribution of the Work otherwise complies with the conditions stated in this License.
5. Submission of Contributions. Unless You explicitly state otherwise, any Contribution intentionally submitted for inclusion in the Work by You to the Licensor shall be under the terms and conditions of this License, without any additional terms or conditions. Notwithstanding the above, nothing herein shall supersede or modify the terms of any separate license agreement you may have executed with Licensor regarding such Contributions.
6. Trademarks. This License does not grant permission to use the trade names, trademarks, service marks, or product names of the Licensor, except as required for reasonable and customary use in describing the origin of the Work and reproducing the content of the NOTICE file.
7. Disclaimer of Warranty. Unless required by applicable law or agreed to in writing, Licensor provides the Work (and each Contributor provides its Contributions) on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied, including, without limitation, any warranties or conditions of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or FITNESS FOR A PARTICULAR PURPOSE. You are solely responsible for determining the appropriateness of using or redistributing the Work and assume any risks associated with Your exercise of permissions under this License.
8. Limitation of Liability. In no event and under no legal theory, whether in tort (including negligence), contract, or otherwise, unless required by applicable law (such as deliberate and grossly negligent acts) or agreed to in writing, shall any Contributor be liable to You for damages, including any direct, indirect, special, incidental, or consequential damages of any character arising as a result of this License or out of the use or inability to use the Work (including but not limited to damages for loss of goodwill, work stoppage, computer failure or malfunction, or any and all other commercial damages or losses), even if such Contributor has been advised of the possibility of such damages.
9. Accepting Warranty or Additional Liability. While redistributing the Work or Derivative Works thereof, You may choose to offer, and charge a fee for, acceptance of support, warranty, indemnity, or other liability obligations and/or rights consistent with this License. However, in accepting such obligations, You may act only on Your own behalf and on Your sole responsibility, not on behalf of any other Contributor, and only if You agree to indemnify, defend, and hold each Contributor harmless for any liability incurred by, or claims asserted against, such Contributor by reason of your accepting any such warranty or additional liability.
END OF TERMS AND CONDITIONS
MIT License
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
BSD licence
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. Neither the name of the copyright holder nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
ISC licence
Permission to use, copy, modify, and/or distribute this software for any purpose with or without fee is hereby granted, provided that the above copyright notice and this permission notice appear in all copies.
THE SOFTWARE IS PROVIDED “AS IS” AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
Mozilla Public License 2.0
Mozilla Public License
Version 2.0
This license applies to the following redistributed libraries and files:- certifi
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
1. Definitions
1.1. “Contributor”means each individual or legal entity that creates, contributes to the creation of, or owns Covered Software.
1.2. “Contributor Version”means the combination of the Contributions of others (if any) used by a Contributor and that particular Contributor’s Contribution.
1.3. “Contribution”means Covered Software of a particular Contributor.
1.4. “Covered Software”means Source Code Form to which the initial Contributor has attached the notice in Exhibit A, the Executable Form of such Source Code Form, and Modifications of such Source Code Form, in each case including portions thereof.
1.5. “Incompatible With Secondary Licenses”meansthat the initial Contributor has attached the notice described in Exhibit B to the Covered Software; orthat the Covered Software was made available under the terms of version 1.1 or earlier of the License, but not also under the terms of a Secondary License.
1.6. “Executable Form”means any form of the work other than Source Code Form.
1.7. “Larger Work”means a work that combines Covered Software with other material, in a separate file or files, that is not Covered Software.
1.8. “License”means this document.
1.9. “Licensable”means having the right to grant, to the maximum extent possible, whether at the time of the initial grant or subsequently, any and all of the rights conveyed by this License.
1.10. “Modifications”means any of the following:any file in Source Code Form that results from an addition to, deletion from, or modification of the contents of Covered Software; orany new file in Source Code Form that contains any Covered Software.
1.11. “Patent Claims” of a Contributormeans any patent claim(s), including without limitation, method, process, and apparatus claims, in any patent Licensable by such Contributor that would be infringed, but for the grant of the License, by the making, using, selling, offering for sale, having made, import, or transfer of either its Contributions or its Contributor Version.
1.12. “Secondary License”means either the GNU General Public License, Version 2.0, the GNU Lesser General Public License, Version 2.1, the GNU Affero General Public License, Version 3.0, or any later versions of those licenses.
1.13. “Source Code Form”means the form of the work preferred for making modifications.
1.14. “You” (or “Your”)means an individual or a legal entity exercising rights under this License. For legal entities, “You” includes any entity that controls, is controlled by, or is under common control with You. For purposes of this definition, “control” means (a) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (b) ownership of more than fifty percent (50%) of the outstanding shares or beneficial ownership of such entity.
2. License Grants and Conditions
2.1. Grants
Each Contributor hereby grants You a world-wide, royalty-free, non-exclusive license:
1. under intellectual property rights (other than patent or trademark) Licensable by such Contributor to use, reproduce, make available, modify, display, perform, distribute, and otherwise exploit its Contributions, either on an unmodified basis, with Modifications, or as part of a Larger Work; and
2. under Patent Claims of such Contributor to make, use, sell, offer for sale, have made, import, and otherwise transfer either its Contributions or its Contributor Version.
2.2. Effective Date
The licenses granted in Section 2.1 with respect to any Contribution become effective for each Contribution on the date the Contributor first distributes such Contribution.
2.3. Limitations on Grant Scope
The licenses granted in this Section 2 are the only rights granted under this License. No additional rights or licenses will be implied from the distribution or licensing of Covered Software under this License. Notwithstanding Section 2.1(b) above, no patent license is granted by a Contributor:
1. for any code that a Contributor has removed from Covered Software; or
2. for infringements caused by: (i) Your and any other third party’s modifications of Covered Software, or (ii) the combination of its Contributions with other software (except as part of its Contributor Version); or
3. under Patent Claims infringed by Covered Software in the absence of its Contributions.
This License does not grant any rights in the trademarks, service marks, or logos of any Contributor (except as may be necessary to comply with the notice requirements in Section 3.4).
2.4. Subsequent Licenses
No Contributor makes additional grants as a result of Your choice to distribute the Covered Software under a subsequent version of this License (see Section 10.2) or under the terms of a Secondary License (if permitted under the terms of Section 3.3).
2.5. Representation
Each Contributor represents that the Contributor believes its Contributions are its original creation(s) or it has sufficient rights to grant the rights to its Contributions conveyed by this License.
2.6. Fair Use
This License is not intended to limit any rights You have under applicable copyright doctrines of fair use, fair dealing, or other equivalents.
2.7. Conditions
Sections 3.1, 3.2, 3.3, and 3.4 are conditions of the licenses granted in Section 2.1.
3. Responsibilities
3.1. Distribution of Source Form
All distribution of Covered Software in Source Code Form, including any Modifications that You create or to which You contribute, must be under the terms of this License. You must inform recipients that the Source Code Form of the Covered Software is governed by the terms of this License, and how they can obtain a copy of this License. You may not attempt to alter or restrict the recipients’ rights in the Source Code Form.
3.2. Distribution of Executable Form
If You distribute Covered Software in Executable Form then:
1. such Covered Software must also be made available in Source Code Form, as described in Section 3.1, and You must inform recipients of the Executable Form how they can obtain a copy of such Source Code Form by reasonable means in a timely manner, at a charge no more than the cost of distribution to the recipient; and
2. You may distribute such Executable Form under the terms of this License, or sublicense it under different terms, provided that the license for the Executable Form does not attempt to limit or alter the recipients’ rights in the Source Code Form under this License.
3.3. Distribution of a Larger Work
You may create and distribute a Larger Work under terms of Your choice, provided that You also comply with the requirements of this License for the Covered Software. If the Larger Work is a combination of Covered Software with a work governed by one or more Secondary Licenses, and the Covered Software is not Incompatible With Secondary Licenses, this License permits You to additionally distribute such Covered Software under the terms of such Secondary License(s), so that the recipient of the Larger Work may, at their option, further distribute the Covered Software under the terms of either this License or such Secondary License(s).
3.4. Notices
You may not remove or alter the substance of any license notices (including copyright notices, patent notices, disclaimers of warranty, or limitations of liability) contained within the Source Code Form of the Covered Software, except that You may alter any license notices to the extent required to remedy known factual inaccuracies.
3.5. Application of Additional Terms
You may choose to offer, and to charge a fee for, warranty, support, indemnity or liability obligations to one or more recipients of Covered Software. However, You may do so only on Your own behalf, and not on behalf of any Contributor. You must make it absolutely clear that any such warranty, support, indemnity, or liability obligation is offered by You alone, and You hereby agree to indemnify every Contributor for any liability incurred by such Contributor as a result of warranty, support, indemnity or liability terms You offer. You may include additional disclaimers of warranty and limitations of liability specific to any jurisdiction.
4. Inability to Comply Due to Statute or Regulation
If it is impossible for You to comply with any of the terms of this License with respect to some or all of the Covered Software due to statute, judicial order, or regulation then You must: (a) comply with the terms of this License to the maximum extent possible; and (b) describe the limitations and the code they affect. Such description must be placed in a text file included with all distributions of the Covered Software under this License. Except to the extent prohibited by statute or regulation, such description must be sufficiently detailed for a recipient of ordinary skill to be able to understand it.
5. Termination
5.1. The rights granted under this License will terminate automatically if You fail to comply with any of its terms. However, if You become compliant, then the rights granted under this License from a particular Contributor are reinstated (a) provisionally, unless and until such Contributor explicitly and finally terminates Your grants, and (b) on an ongoing basis, if such Contributor fails to notify You of the non-compliance by some reasonable means prior to 60 days after You have come back into compliance. Moreover, Your grants from a particular Contributor are reinstated on an ongoing basis if such Contributor notifies You of the non-compliance by some reasonable means, this is the first time You have received notice of non-compliance with this License from such Contributor, and You become compliant prior to 30 days after Your receipt of the notice.
5.2. If You initiate litigation against any entity by asserting a patent infringement claim (excluding declaratory judgment actions, counter-claims, and cross-claims) alleging that a Contributor Version directly or indirectly infringes any patent, then the rights granted to You by any and all Contributors for the Covered Software under Section 2.1 of this License shall terminate.
5.3. In the event of termination under Sections 5.1 or 5.2 above, all end user license agreements (excluding distributors and resellers) which have been validly granted by You or Your distributors under this License prior to termination shall survive termination.
6. Disclaimer of Warranty
Covered Software is provided under this License on an “as is” basis, without warranty of any kind, either expressed, implied, or statutory, including, without limitation, warranties that the Covered Software is free of defects, merchantable, fit for a particular purpose or non-infringing. The entire risk as to the quality and performance of the Covered Software is with You. Should any Covered Software prove defective in any respect, You (not any Contributor) assume the cost of any necessary servicing, repair, or correction. This disclaimer of warranty constitutes an essential part of this License. No use of any Covered Software is authorized under this License except under this disclaimer.
7. Limitation of Liability
Under no circumstances and under no legal theory, whether tort (including negligence), contract, or otherwise, shall any Contributor, or anyone who distributes Covered Software as permitted above, be liable to You for any direct, indirect, special, incidental, or consequential damages of any character including, without limitation, damages for lost profits, loss of goodwill, work stoppage, computer failure or malfunction, or any and all other commercial damages or losses, even if such party shall have been informed of the possibility of such damages. This limitation of liability shall not apply to liability for death or personal injury resulting from such party’s negligence to the extent applicable law prohibits such limitation. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion and limitation may not apply to You.
8. Litigation
Any litigation relating to this License may be brought only in the courts of a jurisdiction where the defendant maintains its principal place of business and such litigation shall be governed by laws of that jurisdiction, without reference to its conflict-of-law provisions. Nothing in this Section shall prevent a party’s ability to bring cross-claims or counter-claims.
9. Miscellaneous
This License represents the complete agreement concerning the subject matter hereof. If any provision of this License is held to be unenforceable, such provision shall be reformed only to the extent necessary to make it enforceable. Any law or regulation which provides that the language of a contract shall be construed against the drafter shall not be used to construe this License against a Contributor.
10. Versions of the License
10.1. New Versions
Mozilla Foundation is the license steward. Except as provided in Section 10.3, no one other than the license steward has the right to modify or publish new versions of this License. Each version will be given a distinguishing version number.
10.2. Effect of New Versions
You may distribute the Covered Software under the terms of the version of the License under which You originally received the Covered Software, or under the terms of any subsequent version published by the license steward.
10.3. Modified Versions
If you create software not governed by this License, and you want to create a new license for such software, you may create and use a modified version of this License if you rename the license and remove any references to the name of the license steward (except to note that such modified license differs from this License).
10.4. Distributing Source Code Form that is Incompatible With Secondary Licenses
If You choose to distribute Source Code Form that is Incompatible With Secondary Licenses under the terms of this version of the License, the notice described in Exhibit B of this License must be attached.
Exhibit A - Source Code Form License Notice
This Source Code Form is subject to the terms of the Mozilla Public License, v. 2.0. If a copy of the MPL was not distributed with this file, You can obtain one at https://mozilla.org/MPL/2.0/.
If it is not possible or desirable to put the notice in a particular file, then You may include the notice in a location (such as a LICENSE file in a relevant directory) where a recipient would be likely to look for such a notice.
<Backpage>
</Backpage>
Back page
 |
Hersteller / Manufacturer: |
DÜRR DENTAL SE Höpfigheimer Str. 17 74321 Bietigheim-Bissingen Germany Fon: +49 7142 705-0 www.duerrdental.com info@duerrdental.com |
</Backpage>